filter-manufacture,factory,supplier from China

1. Check the condition of the pressure gauge to see if it is working properly.2. Check the pressure values of pressure gauge 1 and pressure gauge 2, when the difference between the pressure values of the two pressure gauges exceeds 0.02GP, clean the filter screen.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

Precise filtration: Filter discs with exceptional precisions may be selected in step with the water requirements. There are 20 microns, 55 microns, one hundred microns, 130 microns, two hundred microns, 400 microns and other specifications, and the filtration ratio is extra than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

The stack clean out is composed of a hard and fast of plates with grooves on each sides. the intersection point shaped with the resource of the rims of the grooves can intercept the solids in the water.

Components used in drip irrigation (listed in order from water source) include: Pump or pressurized water source. Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional) Backwash controller (Backflow prevention device)

FeaturesColor: As the pix shown.Material: ABS, plastic.Premium quality - 3 arm + ABS plastic rotary garden sprinkler with Ground Rod.Effective water sprinkler irrigation machine - patented layout of water-saving tool may be centered to keep water maximum with the aid of using adjusting the water density, length and scope.Easy use - join water joint to the connector and tap.Long spray distance - as much as 26ft-32.8ft distance with worldwide general pipes.Different spray direction - direct or forty five degree.Spraying distance: upward 2.5-3m, lateral 4-5m Connection length: half of Inch M

Compared with the dripper, the most obvious feature of the pressure-compensated dripper is:1. The pressure compensation dripper can make the elastic silicone sheet change the section of the water outlet with the help of water conservancy pressure, automatically adjust the flow rate, and make the water output uniform;2. The pressure compensation performance is strong, and the automatic control water dispenser is the best choice. It is especially suitable for undulating terrain, unbalanced system pressure and need to increase capillary.How to choose a pressure compensation dripper?1.

The Merits of Drip IrrigationAdvantages of any kind of watering rely On the types of vegetation grown, how properly the Weather behaves, and the plant overall performance You preference.

Based on the definition and connotation of the above-mentioned water-saving products, it can be divided into the following categories from the principles and approaches of water-saving:(1) Products that directly improve the use efficiency of water resourcesIt is a water-consumable product, and it can reduce water consumption compared to similar products under the condition of fulfilling the same function.(2) Products that reduce the loss of water resources and prevent pollutionIn the process of use, it does not consume water resources, but it can ensure that water resources are not lost and po

1. AdvantagesSave water, fertilizer and laborDrip irrigation is a full pipeline water delivery and local micro-irrigation, which reduces the leakage and loss of water to the lowest limit. At the same time, because it can supply the water required by the crop root zone in a timely manner, there is no problem of peripheral water loss, and the water use efficiency is greatly improved. Irrigation can be conveniently combined with fertilization, that is, dissolve the chemical fertilizer and pour it into the irrigation system.

Pipe failure in long-term applications is characterised by creep crack initiation and creep crack growth. Both can be determined by fracture mechanics-based tests of the pipe materials. Nowadays, several accelerated tests are available: Considering new fiber composite polyethylene (pe) substances are contemplated for use by means of fuel industry, a chief assignment is to carry out a computational evaluation for the cracked and uncracked pipes. That is completed using a completely unique finite detail code pfrac.

Pressure CompensationThe amount of pressure that flows through a drip irrigation system can fluctuate, depending on hose length and garden bed elevation, among other factors. This can cause emitters to flow differently than designed, with more or less water flow depending on pressure.To combat this, the best drip irrigation system emitters are pressure compensating by design. They’ll emit the same amount of water regardless of the pressure at their inlet (where they attach to the main hose).